Heat Sealers
Impulse Heat Sealers and Shrink Heat Guns
Benchtop bag sealers in 2mm, 5mm and 10mm seal widths, plus an LPG heat gun for shrink film and pallet covers
Our impulse heat sealers give you a clean, airtight seal on polythene and polypropylene bags and tubing in a couple of seconds. Set the timer, press the handle down, and the element heats only while the jaw is closed, so there's no warm-up and the machine stays cool between seals. They're a simple, low-cost way to keep food fresh, stop contamination and make parts and samples tamper-evident. Replacement elements and PTFE strips are available from our service team, so your sealer keeps working for years. For bigger jobs, our LPG shrink heat gun shrinks pallet covers, pallet bags and shrink film tight around a load.
Not sure what you need? Compare seal widths below, or tell us what you're sealing and we'll recommend one.
Why use an impulse heat sealer?
Tape, twist ties and clips can come loose. A heat seal fuses the bag closed, keeping moisture, dust and air out and showing straight away if a pack has been opened.
How to choose the right heat sealer
Start with three questions: how wide is your bag, how thick is the film, and do you need to trim it?
Sealing length
Choose a sealer at least as long as your widest bag opening, with a little to spare.
Seal width and film thickness
A wider seal is stronger and handles thicker film. Our standard benchtop models seal bags up to 2 x 200 microns.
Cutter or no cutter
If you make bags from tubing or want a tidy finish, a model with a sliding cutter seals and trims in one step.
Cutter models by seal width
| Seal width | Film thickness | Sealing lengths | Best for |
|---|---|---|---|
| 2mm | Up to 2 x 150 microns | 200, 300 and 400mm | Light bags and tubing, everyday packing benches |
| 5mm | Up to 2 x 300 microns | 200 and 300mm | Thicker bags, food packs and a stronger, neater seal |
| 10mm | Heavy-duty (1000W) | Ask us | The widest, strongest seal for heavier film and demanding jobs |
We can also supply special-purpose sealers with magnetic hold-down and automatic timing for higher-volume work. Ask us about the right setup for your line.
Not Sure Which Sealer Suits Your Bags?
Tell us your bag width, film type and thickness, and how many you seal a day. Our Villawood team will recommend the right sealer and send you pricing.
Power Packaging Pty Ltd | Dispatching daily from our Sydney warehouse
Getting a good seal
1. Keep the bag mouth clean and flat
Product, dust or moisture in the seal area stops the film fusing. Smooth out any creases before you seal.
2. Set the timer for the film
Too little heat leaves a weak seal that peels. Too much thins or burns the film. Test on a spare bag first.
3. Hold, then release
Keep the handle down for a moment after the light goes out so the seal cools under pressure.
LPG shrink heat gun for pallets and large packs
When the job is too big for a benchtop sealer, our shrink heat gun does the work. Run on LPG (propane), it shrinks polythene pallet covers, pallet bags, poly sheeting and shrink film tight around the load, giving you a weatherproof, tidy finish for storage, shipping or display.
Using it safely
Use the heat gun in a well-ventilated area, keep it away from flammable materials, and follow the operating and gas safety instructions supplied with it. Keep the flame moving so the film shrinks evenly without burning through. Pair it with our pallet bags and pallet tube or poly sheet.
Spare elements and PTFE strips
The heating element and the PTFE (Teflon) strip covering it are the parts that wear. If your seals start to look uneven, scorched or patchy, it's usually time to replace them. Contact our service team with your sealer's code and we'll supply the right parts.
Need bags to seal? See our poly bags, poly tube and press seal bags, or browse our full packaging machinery range.
Frequently Asked Questions
What is an impulse heat sealer?
A sealer that sends a short burst of power to the element only while the jaw is closed. The film is heated, the power cuts off, and the seal cools under pressure. That means no warm-up time, less power used, and a cooler machine on the bench.
What bags can I seal?
Polythene (PE) and polypropylene (PP) bags and tubing. If you're sealing a laminate, foil or coated bag, send us a sample or details and we'll check it suits.
Which seal width should I choose?
A 2mm seal suits most light bags. Choose 5mm for thicker film, food packs or a neater, stronger finish, and 10mm for the heaviest film and jobs where seal strength matters most.
How do I set the timer?
Start low and increase it a step at a time until the seal is fully fused but not stretched, thin or burnt. Thicker film needs a longer setting.
Do you sell replacement elements and PTFE strips?
Yes. Elements and PTFE (Teflon) strips wear over time. Contact our service team with your sealer's code and we'll supply the right parts.
Can I seal and cut in one step?
Yes. Our cutter models have a sliding blade, so you can seal and trim the excess film in one pass. They're especially handy when you make bags from tubing.
What can the shrink heat gun be used on?
Polythene pallet covers, pallet bags, poly sheeting and shrink film. It runs on LPG (propane), so use it in a well-ventilated area, away from flammable materials, and follow the safety instructions supplied with it.
Enquire About Heat Sealers and Shrink Guns
Looking for the right sealer or shrink gun, a quote, or replacement elements and PTFE strips?